| 161.50.2800.891.41.1503 Standard 5 Slewing Ring Bearings | N1:22.225 mm; Ca:62.789 mm; P120°:55.6 kN; End plug (suffix Y):EPR 13; da:96.838 mm; Cap bolt recommended tightening torque:203.4 N·m; H1:125.425 mm; H:239.316 mm; Cap bolt:2 x 3/4-10 UNC; R1:67.866 mm; Da:200 mm; J max.:368.3 mm; Housing:SAF 522; J min.:320.675 mm; h:45.244 mm; PG:1/4 NPT; P180°:60.9 kN; P150°:50.7 kN; L:419.1 mm; Max. speed for PosiTrac Plus seal:1450 r/min; |
| 8 0405 05 Rollix Slewing Ring Bearings | N1:23.813 mm; A1:88.9 mm; Cap bolt recommended tightening torque:298.3 N·m; End plug (suffix Y):EPR 9; Taconite seal:TER 52; J min.:250.825 mm; L:330.2 mm; R2:22.225 mm; P90°:47.2 kN; P60°:78.7 kN; H2:38.1 mm; da:73.025 mm; P120°:28.9 kN; Housing:SAFS 517; RG:3/8 NPT; Max. speed for Taconite seal:1050 r/min; Stabilizing ring:SR-17-14; Appropriate attachment bolt size G:0.75 in; S:4.763 mm; |
| 24 0941 01 Rollix Slewing Ring Bearings | H1:88.9 mm; Cap bolt, SAE grade:8; Cap bolt recommended tightening torque:298.3 N·m; da:53.975 mm; P90°:36 kN; Mass pillow block:17.1 kg; End plug (suffix Y):EPR 7; Stabilizing ring:2 x SR-1613; Ca:57.785 mm; Initial grease fill:175.77 g; H:167.481 mm; R1:53.181 mm; J1:53.975 mm; J min.:244.475 mm; P60°:60.5 kN; Max. speed for Taconite seal:1400 r/min; Taconite seal:TER 31; Housing:FSAF 613; |
| 161.45.2510.891.41.1503 Standard 5 Slewing Ring Bearings | ra (max):1.5 mm; Dynamic Load Rating:62,500 N; Radial Clearance:0.020 to 0.045 mm; dc (min):47 mm; Fillet Radius/Chamfer:1.5 mm; dd (min):52 mm; d:30 mm; ra1 (max):1.5 mm; Da (max):81.5 mm; Bore Type:Cylindrical Bore; db (max):44 mm; Static Load Rating:55,000 N; Limiting Speed - Grease:7,500 rpm; Limiting Speed - Oil:9,500 rpm; D:90 mm; Enclosure:Open; Configuration:Single Row; Inside Ring Outside Diameter:45 mm; |
| 2 0245 Rollix Slewing Ring Bearings | Fillet Radius/Chamfer:2.1 mm; ra (max):2 mm; a (max):5.7 mm; d:105 mm; r1:0.5 mm; Factor fo:14.3; Cy (max):8.4 mm; da (min):117 mm; Configuration:Single Row; Radial Clearance:0.036 to 0.066 mm; Bore Type:Cylindrical Bore; Snap Ring Outside Diameter:202.9 mm; Limiting Speed - Grease:3,400 rpm; Limiting Speed - Oil:4,000 rpm; Enclosure:Snap Ring Groove wit; b (min):3.5 mm; Snap Ring Width:3.1 mm; Da (max):178 mm; |
| 26 0741 01 Rollix Slewing Ring Bearings | D:480 mm; B:130 mm; db (min):282 mm; Limiting Speed - Grease:1,100 rpm; ra (max):4 mm; dd (min):343 mm; Fillet Radius/Chamfer:5 mm; Da (max):458 mm; Enclosure:Open; Radial Clearance:0.125 to 0.195 mm; db (max):318 mm; Configuration:Single Row; d:260 mm; Bore Type:Cylindrical Bore; Static Load Rating:2,930,000 N; Dynamic Load Rating:1,780,000 N; dc (min):323 mm; r1:5 mm; Inside Ring Outside Diameter:320 mm; |
| 12.30.2538.001.41.1503 Standard 5 Slewing Ring Bearings | Ca:196 mm; ba max.:170 mm; Da:500 mm; N1:42 mm; ATS:360 mm; J6:770 mm; Bearing (basic designation):23256 K; Cap bolt, size:M 30x220; H1:300 mm; P55°:6000 kN; da:265.113 mm; Eye bolt, size:2 x M 30; P90°:2900 kN; Locating ring:2 x FRB 10/500; Appropriate attachment bolt, size G:36 mm; s:22 mm; J1:190 mm; Labyrinth seal:2 x TS 60/10.7/16; Pa:1200 kN; Initial grease fill, 40%:5.6 kg; |
| 27 0941 01 Rollix Slewing Ring Bearings | J1:57.15 mm; PG:1/8 NPT; R1:73.025 mm; Cap bolt:2 x 3/4-10 UNC; P120°:48.9 kN; J max.:342.9 mm; S:4.763 mm; Stabilizing ring:SR-21-18; Cap bolt recommended tightening torque:515.2 N·m; Cap bolt, SAE grade:8; Pa:17.3 kN; Mass pillow block:44 kg; Appropriate attachment bolt size G:0.75 in; H:230.981 mm; N1:22.225 mm; A2:174.625 mm; Initial grease fill:232.47 g; Housing:SAF 618; H2:50.8 mm; |
| 1 0289 06 Rollix Slewing Ring Bearings | r1:0.5 mm; Fillet Radius/Chamfer:3 mm; Dynamic Load Rating:153,000 N; a (max):5.7 mm; Bore Type:Cylindrical Bore; ra (max):2.5 mm; Weight:5.670 kg; D:200 mm; Limiting Speed - Grease:3,300 rpm; b (min):3.5 mm; Configuration:Single Row; d:95 mm; Cy (max):8.4 mm; da (min):109 mm; Static Load Rating:118,000 N; Da (max):186 mm; Radial Clearance:0.030 to 0.058 mm; D1 (max):193.7 mm; Enclosure:Single Shield with S; |
| 121.50.6000.990.41.1502 Standard 5 Slewing Ring Bearings | Cap bolt:2 x 1-8 UNC; Cap bolt recommended tightening torque:1220 N·m; Stabilizing ring:2 x 36053-50; A1:120.65 mm; P120°:72.5 kN; P150°:66.7 kN; P90°:111 kN; H2:53.975 mm; Ca:72.619 mm; R2:30.163 mm; Cap bolt, SAE grade:8; Pa:22.2 kN; L:419.1 mm; Max. speed for Taconite seal:625 r/min; da:123.825 mm; Taconite seal:TER 121; End plug (suffix Y):EPR 27; A2:255.588 mm; N1:22.225 mm; |